Pancake slip ring and its features

  • 6 years   ago
Pancake slip ring and its features

Pancake slip ring has a conductor that arranged flat ring concentric rings centered in the rotating shaft. It improved mechanical performance. Basically, these are used in alternators, slip ring motors, electrical generators, AC (alternating current), and wind turbines.

A pancake slip ring is produced for space critical application for height dimension. Basically, they are designed for rotation system. They are designed for vertical space that is limited other than horizontal space as much restrictive. They are designed for limited height that doesn’t have any limitation in OD. This slip ring has many features in heaviness and height. It just looked like a CD or like a plate that is why also called a plate slip ring or flat slip ring. It has a precious metal brush with high transmitting and rotating. It also has a special vacuum volume. The client always chooses radial cable output with normal height and axial cable output. It has low maintenance, table, low noise, torque, and long life. They use metal contacts that are stable low resistance and performance. It depends on customer’s requirement we offered two different pancake slip ring one is industrial and the second one is common quality. 

 

Pancake slip ring for housing

Make sure about the equipment of room installation when you select the model.  Your room rotating part is limited when you start using a series of the pancake slip ring. There are different colors in a ring. You got in red, brown, black, yellow, green, orange, purple, grey, blue, white, and so on. If you use pancake slip ring for housing so, use the best one fiber brush and metal to gold – gold multi contacting material. It has a long lifetime low contact pressure. They provide low electrical noise for high data rate transmission. 

It saves a lot of space with the copper ring and brushes contact which is in the central hole. There are many features in them like high rotating speed, transmitting power and signal, extreme low physical noise, light figure, drop the connection, and unfailing contact. Mechanically it has operating speed is about 0-300rpm, the thickness is about 6mm to 63mm, shock resistance is 30g, inner diameter is about 4mm to 820mm, outer diameter is about 21mm to 220mm, and torque 0.05N.m. The slip ring current rating is 30A per circuit and voltage rating is 380 VAC. The slip ring is used to conduct electricity through vacuum and hydraulic. They are transmitted various signals to the device where 360 rotating. The pancake slip ring transmits current and signals channel by infinite transverse on ring number diameter. They are usually used to transmit signals together with power. They are also used to combine fluid media like hydraulic and pneumatic. After searching and get experience this thing is proving that pancake slip ring has a mature technology. 

There are different types of slip ring. Here discuss some of them

 

    Product                                                       thickness                 IDmm                   Rings                   

1. 210                                                       20mm                       12.7                    2-24                                                              

2. 220                                                       22mm                        25.4                   2-24

3. 240                                                       30mm                       40                       2-24  

4. 250                                                       30mm                       50                       2-24

5. 270                                                       30mm                       70                       2-18

6. 310                                                       15.8-27mm               12.7                    2-18

7. 320                                                       17.1-30.7mm            25.4                    2-18

8. 340                                                       17.1-30.7mm            40                       2-18

9. 350                                                       17.1-30.7mm            50                       2-18

10. 370                                               17.5-29.5mm            70                       2-18

11. 380                                                18.2-31mm              80                       2-18

All detail of the MP’s is given below

1-Mp 210 

The MP210 series pancake slip ring is used metal contact and gold processing plate that can transfer stable signals and power with little resistance fluctuations. The Mp210 slip ring has a 20mm thickness with an aluminum structure. And it is designed for the thicker requirement which thickness is restrictive except diameter has less. The VC product max speed is 60rpm and VD product speed is about 200rpm. It is worked mechanically and electrically. They have a different specification for both. 

Mechanical features

Torque                                                                  0.1N.m+0.03/6ring

Operating humidity                                               0-85%RH

Rotating speed                                                     Quality level 

Protection grade                                                   ip51

Contact material                                                 Quality level

Working temp                                                     -30 to 80 degree C

Housing material                                                 Aluminum alloy 

Parameter                                                            Value

Electrically features 

Res noise                                                          0.01

Parameter                                                          Value 

Lead wires                                                       AWG16#TEFLON and AWG22#TEFLON

Dielectric strength                                            500VAC at 50 Hz, 60 

Lead length                                                        300mm

Rated voltage                                                     0-440 VAC/VDC and 0-240 VAC/VDC 

Insulation res                                                     1000 M/ 500 VDC

 

2- MP220 

The Mp220 series pancake slip ring is used metal contact for transferring the signals with small resistance fluctuation. They have thickness is about 22mm, ID is about 25.4mm, and 1-48 slip ring. It is also used as mechanically and electrically. The features are listed below

Mechanically features

Torque                                                           0.05N.m +0.03/6ring

Working temp                                                    -30 - 80 degree C            

Rotating speed                                                  Quality level 

Parameter                                                             value 

Contact material                                               Quality level 

Protection guide                                              ip51

Housing Material                                             Aluminum Alloy

Operating humidity                                        0-85% RH

Working lite                                                      Quality level 

Electrically features

Res noise                                                              0.01                                  

Parameter                                                             value

Lead wires                                                       AWG16#Teflon and AWG22#Teflon

Dielectric strength                                             500VAC at 50 Hz, 60

Lead length                                                          300mm

Rated voltage                                                     0-440 VAC/VDC and 0-240 VAC/VDC

Insulation res                                                    1000M/ 500VDC 

 

3-Mp240

The Mp240 series pancake slip ring is used metallic plates for transmitting signals and power. It has ID 40mm; thickness is 30mm and 1-24rings. The product quality level VC is 60rpm and VD is 200rpm. They have many features in them. They used mechanically and electrically. 

Mechanically features 

Torque                                                           0.05N.m +0.03/6ring

Working temp                                                    -30 - 80 degree C            

Rotating speed                                                  Quality level 

Parameter                                                             value 

Contact material                                               Quality level 

Protection guide                                              ip51

Housing Material                                             Aluminum Alloy

Operating humidity                                        0-85% RH

Working lite                                                      Quality level 

Electrically features

Res noise                                                              0.01                                  

Parameter                                                             value

Lead wires                                                       AWG16#Teflon and AWG22#Teflon

Dielectric strength                                             500VAC at 50 Hz, 60

Lead length                                                          300mm

Rated voltage                                                     0-440 VAC/VDC and 0-240 VAC/VDC

Insulation res                                                    1000M/ 500VDC 

4-Mp250 

It has a 30mm thickness with aluminum alloy, ID 50mm, and 1-24 rings. It is designed for min thicker requirement that is restrictive but less in diameter. It also transmits signal and power with resistance. It is also used as mechanical and electric needs. They have different features in them that are useful for you to know about that. The features are given below

Mechanically features 

Torque                                                           0.05N.m +0.03/6ring

Working temp                                                    -30 - 80 degree C            

Rotating speed                                                  Quality level 

Parameter                                                             value 

Contact material                                               Quality level 

Protection guide                                              ip51

Housing Material                                             Aluminum Alloy

Operating humidity                                        0-85% RH

Working lite                                                      Quality level 

Electrically features

Res noise                                                              0.01                                  

Parameter                                                             value

Lead wires                                                       AWG16#Teflon and AWG22#Teflon

Dielectric strength                                             500VAC at 50 Hz, 60

Lead length                                                          300mm

Rated voltage                                                     0-440 VAC/VDC and 0-240 VAC/VDC

Insulation res                                                    1000M/ 500VDC  

4-Mp250 

The slip ring is transmitting signals and power with small resistance fluctuation. It is used gold plates and contact material. It has 50mm, the thickness is about 30mm, and 1-24 rings. It has also different features and these features are given below

Mechanically features 

Torque                                                           0.05N.m +0.03/6ring

Working temp                                                    -30 - 80 degree C            

Rotating speed                                                  Quality level 

Parameter                                                             value 

Contact material                                               Quality level 

Protection guide                                              ip51

Housing Material                                             Aluminum Alloy

Operating humidity                                        0-85% RH

Working lite                                                      Quality level 

Electrically features

Res noise                                                              0.01                                  

Parameter                                                             value

Lead wires                                                       AWG16#Teflon and AWG22#Teflon

Dielectric strength                                             500VAC at 50 Hz, 60

Lead length                                                          300mm

Rated voltage                                                     0-440 VAC/VDC and 0-240 VAC/VDC

Insulation res                                                    1000M/ 500VDC  

Almost the features are the same but the ID, thickness, and rings are different.

Comments